Fluids Worksheet with Answer Key

11 problems on fluids, ready to print for class or homework. The answer key prints on its own page, so hand out everything before it.

  1. 1. Density of a rectangular slab

    A solid rectangular slab measures 0.30 m by 0.15 m by 0.020 m and has a mass of 1.26 kg. (a) Find its density. (b) Express that in grams per cubic centimetre. (c) Will it float or sink in fresh water, of density 1000 kg/m31000\ \text{kg/m}^3? (d) A second slab of the same material has twice the volume. What are its mass and its density?

  2. 2. The same block, two different pressures

    A rectangular block of weight 84 N rests on a flat table. Its base measures 0.30 m by 0.14 m. (a) Find the pressure it exerts on the table. (b) The block is tipped onto a face measuring 0.14 m by 0.060 m. Find the new pressure. (c) By what factor did the pressure change, and why did the weight not? (d) Express the larger pressure as a fraction of one atmosphere.

  3. 3. Gauge and absolute pressure in an open tank

    A storage tank with vertical sides and a flat bottom of area 0.80 m20.80\ \text{m}^2 is open to the atmosphere and holds a liquid of density 1250 kg/m31250\ \text{kg/m}^3 to a depth of 3.20 m. Take atmospheric pressure as 1.0×105 Pa1.0 \times 10^5\ \text{Pa} and g=9.8 m/s2g = 9.8\ \text{m/s}^2. Find (a) the gauge pressure at the bottom, (b) the absolute pressure at the bottom, (c) the gauge pressure 1.20 m below the surface, and (d) the total downward force on the bottom, separated into the atmosphere's share and the liquid's share.

  4. 4. Oil floating on water in a U-tube

    A U-shaped tube open at both ends holds water of density 1000 kg/m31000\ \text{kg/m}^3. Oil of density 800 kg/m3800\ \text{kg/m}^3 is poured slowly into the left arm, where it floats on the water without mixing, until the oil column is 0.150 m tall. Find (a) the height of the water in the right arm above the oil-water interface in the left arm, and (b) how far the top of the oil stands above the top of the water in the right arm.

  5. 5. A submerged block, and the density that gets grabbed by mistake

    A solid block of volume 3.0×10−3 m33.0 \times 10^{-3}\ \text{m}^3 and mass 8.4 kg is held completely under fresh water of density 1000 kg/m31000\ \text{kg/m}^3. Use g=9.8 m/s2g = 9.8\ \text{m/s}^2. Find (a) the buoyant force on it, (b) its weight, (c) the reading on a spring scale holding it while it is submerged, (d) whether it floats or sinks when released, and (e) its acceleration at the instant of release.

  6. 6. A floating block, and how much of it is under

    A block of wood floats in fresh water (1000 kg/m31000\ \text{kg/m}^3) with 0.72 of its volume below the surface. (a) Find the wood's density. (b) The same block is moved to a liquid of density 1300 kg/m31300\ \text{kg/m}^3. What fraction is submerged now? (c) A block of this wood has a mass of 0.90 kg. What volume of fresh water does it displace while floating, and what is the block's own volume?

  7. 7. How much load can the raft carry?

    A foam raft has a total volume of 0.240 m30.240\ \text{m}^3 and a mass of 36 kg. It floats in fresh water (1000 kg/m31000\ \text{kg/m}^3). Use g=9.8 m/s2g = 9.8\ \text{m/s}^2. Find (a) the fraction of the raft that is submerged when it floats empty, (b) the largest load it can carry before water reaches its top surface, and (c) the fraction submerged when it carries a 150 kg load.

  8. 8. Continuity: the same water through a narrower pipe

    Water flows steadily through a horizontal pipe that is completely full. In the wide section the inside diameter is 8.0 cm and the water moves at 1.20 m/s. Further along, the pipe narrows to an inside diameter of 3.0 cm. Find (a) the volume flow rate, (b) the water's speed in the narrow section, and (c) how long it takes to fill a 25 L container from the open end.

  9. 9. Bernoulli across a constriction

    Water of density 1000 kg/m31000\ \text{kg/m}^3 flows steadily through a horizontal pipe. At point 1 the cross-sectional area is 1.20×10−3 m21.20 \times 10^{-3}\ \text{m}^2, the speed is 1.50 m/s and the absolute pressure is 1.80×105 Pa1.80 \times 10^5\ \text{Pa}. At point 2 the pipe has narrowed to 4.0×10−4 m24.0 \times 10^{-4}\ \text{m}^2. Find (a) the speed at point 2, (b) the absolute pressure at point 2, and (c) both pressures expressed as gauge pressures, taking atmospheric pressure as 1.0×105 Pa1.0 \times 10^5\ \text{Pa}.

  10. 10. A balloon in air, where the fluid is a gas

    A balloon of volume 0.85 m30.85\ \text{m}^3 is filled with helium of density 0.18 kg/m30.18\ \text{kg/m}^3. The balloon skin plus its attached payload have a combined mass of 0.60 kg. The surrounding air has density 1.20 kg/m31.20\ \text{kg/m}^3. Use g=9.8 m/s2g = 9.8\ \text{m/s}^2 and ignore air resistance. Find (a) the buoyant force on the balloon, (b) its total weight, (c) whether it rises or falls when released, and (d) the extra payload that would make it hover.

  11. 11. Three claims about buoyancy, and why each one fails

    A student makes three claims. (a) A steel ship must sink, because steel is about eight times denser than water. (b) A wooden block that floats in fresh water will float lower in salt water, because salt water is heavier. (c) A fully submerged block feels a larger buoyant force the deeper it goes, because the pressure down there is greater. Decide which claims survive, and correct the ones that do not, arguing from Fb=ρVgF_b = \rho V g rather than from intuition.

Fluids: answer key

  1. (a) ρ=1400 kg/m3\rho = 1400\ \text{kg/m}^3. (b) 1.4 g/cm31.4\ \text{g/cm}^3. (c) It sinks, because 1400 is greater than the 1000 kg/m31000\ \text{kg/m}^3 of fresh water. (d) The mass doubles to 2.52 kg and the density is unchanged at 1400 kg/m31400\ \text{kg/m}^3.

  2. (a) P1=2000 PaP_1 = 2000\ \text{Pa}. (b) P2=10000 PaP_2 = 10000\ \text{Pa}. (c) Five times larger, the exact inverse of the area ratio; the weight is unchanged because tipping the block changes how the force is spread, not how much of it there is. (d) 0.100.10 atm.

  3. (a) Pgauge=3.92×104 PaP_{\text{gauge}} = 3.92 \times 10^4\ \text{Pa}. (b) Pabs=1.392×105 PaP_{\text{abs}} = 1.392 \times 10^5\ \text{Pa}. (c) 1.47×104 Pa1.47 \times 10^4\ \text{Pa} gauge at 1.20 m. (d) 1.11×105 N1.11 \times 10^5\ \text{N} in total: 8.0×104 N8.0 \times 10^4\ \text{N} from the atmosphere and 3.136×104 N3.136 \times 10^4\ \text{N} from the liquid, which is exactly the liquid's own weight.

  4. (a) The water in the right arm stands 0.120 m0.120\ \text{m} above the oil-water interface. (b) The top of the oil is 0.030 m0.030\ \text{m} higher than the top of the water. The oil column has to be taller by the inverse density ratio, 1000/800=1.251000/800 = 1.25, because equal pressures at the interface level mean equal weight per unit area.

  5. (a) Fb=29.4 NF_b = 29.4\ \text{N} up. (b) W=82.32 NW = 82.32\ \text{N} down. (c) The scale reads 52.92 N52.92\ \text{N}. (d) It sinks: ρobject=2800 kg/m3\rho_{\text{object}} = 2800\ \text{kg/m}^3 against the water's 1000. (e) 6.3 m/s26.3\ \text{m/s}^2 downward. Using the object's density in Fb=ρVgF_b = \rho V g would have given 82.32 N, exactly the weight, and predicted the block hovering.

  6. (a) ρwood=720 kg/m3\rho_{\text{wood}} = 720\ \text{kg/m}^3. (b) 0.5540.554, just over half, so the block floats higher in the denser liquid. (c) It displaces 9.0×10−4 m39.0 \times 10^{-4}\ \text{m}^3 of water, and the block's own volume is 1.25×10−3 m31.25 \times 10^{-3}\ \text{m}^3; the ratio is 0.72, as part (a) requires.

  7. (a) 0.15, so 15 percent of the raft is under water when empty. (b) 204 kg204\ \text{kg} of load, which brings the total to the 240 kg of water the raft's full volume can displace. (c) 0.775, so 77.5 percent submerged.

  8. (a) Q=6.03×10−3 m3/sQ = 6.03 \times 10^{-3}\ \text{m}^3/\text{s}, about 6.0 L/s6.0\ \text{L/s}. (b) v2=8.53 m/sv_2 = 8.53\ \text{m/s}, faster by the square of the diameter ratio. (c) About 4.1 s4.1\ \text{s} to fill 25 L.

  9. (a) v2=4.50 m/sv_2 = 4.50\ \text{m/s}, three times faster because the area fell to a third. (b) P2=1.71×105 PaP_2 = 1.71 \times 10^5\ \text{Pa} absolute, a drop of 9000 Pa. (c) 0.80×105 Pa0.80 \times 10^5\ \text{Pa} and 0.71×105 Pa0.71 \times 10^5\ \text{Pa} gauge. Pressure is lower where the water moves faster.

  10. (a) Fb=10.0 NF_b = 10.0\ \text{N} up. (b) W=7.38 NW = 7.38\ \text{N} down, including 0.153 kg of helium. (c) It rises, with a net force of 2.62 N2.62\ \text{N}; its average density of 0.886 kg/m30.886\ \text{kg/m}^3 is below the air's 1.20. (d) An extra 0.267 kg0.267\ \text{kg} makes it hover. Using helium's density in FbF_b instead of air's gives 1.50 N and predicts the balloon sinking.

  11. None of the three survives. (a) Ships float because a hull encloses air, so the object's average density, not the steel's, is what competes with the water's; the displaced volume is the hull below the waterline. (b) Backwards: the submerged fraction is ρobject/ρfluid\rho_{\text{object}}/\rho_{\text{fluid}}, so a denser fluid makes the block float higher. Wood at 720 kg/m3720\ \text{kg/m}^3 sits 0.72 submerged in water and 0.554 submerged in a 1300 kg/m31300\ \text{kg/m}^3 liquid. (c) The pressures on the top and bottom faces both rise by the same amount with depth, so their difference, which is the buoyant force, does not change. No depth appears in Fb=ρVgF_b = \rho V g. The one exception is a compressible object, whose volume shrinks with depth.

The key gives final answers only. The full worked solution for each problem is on the matching practice set, and every other sheet is on the worksheets page.