Friction Worksheet with Answer Key

11 problems on friction, ready to print for class or homework. The answer key prints on its own page, so hand out everything before it.

  1. 1. Kinetic friction from a known normal force

    A crate slides across a level warehouse floor. The floor pushes up on the crate with a normal force of 240 N, and the coefficient of kinetic friction between the crate and the floor is μk=0.28\mu_k = 0.28. Find the magnitude of the kinetic friction force on the crate.

  2. 2. Kinetic friction when you are given the mass instead

    A 15 kg toolbox slides across a level concrete floor. Nothing touches it vertically except gravity and the floor. The coefficient of kinetic friction between the toolbox and the floor is μk=0.42\mu_k = 0.42. Find the normal force on the toolbox and the kinetic friction force acting on it.

  3. 3. Working backwards to the coefficient

    A force sensor drags a 3.4 kg wooden block horizontally across a level lab bench at a steady 0.20 m/s. The sensor reads a constant 8.6 N throughout. Find the coefficient of kinetic friction between the block and the bench.

  4. 4. Does it move at all? Static versus kinetic

    A 26 kg crate sits at rest on a level floor. The coefficients between crate and floor are μs=0.62\mu_s = 0.62 and μk=0.48\mu_k = 0.48. (a) A worker pushes horizontally with 140 N. Does the crate start to move, and what friction force acts on it? (b) What is the smallest horizontal push that would get it moving? (c) With the crate now sliding, the worker settles to a steady 200 N horizontal push. Find the crate's acceleration.

  5. 5. An angled pull, where the normal force is not mg

    A 9.0 kg box is dragged along a level floor by a rope held at 28∘28^\circ above the horizontal. The tension in the rope is 45 N and the coefficient of kinetic friction between box and floor is μk=0.22\mu_k = 0.22. Find the normal force on the box, the kinetic friction force, and the box's acceleration.

  6. 6. A block that stays put on a ramp

    A 7.5 kg box rests on a plank tilted at 21∘21^\circ above the horizontal. The coefficient of static friction between box and plank is μs=0.58\mu_s = 0.58. Does the box slide? What friction force actually acts on it, and what is the largest friction force this surface could supply at this angle?

  7. 7. The critical angle, where the surface lets go

    A steel washer rests on a flat steel plate. The coefficient of static friction between them is μs=0.74\mu_s = 0.74. One edge of the plate is raised slowly from horizontal. At what angle does the washer begin to slide, and would stacking a second identical washer on top change that angle?

  8. 8. A block that does slide, and how fast it gets going

    An 11 kg block is released from rest on a ramp inclined at 42∘42^\circ above the horizontal and slides down it. The coefficient of kinetic friction between block and ramp is μk=0.31\mu_k = 0.31. Find the friction force on the block, its acceleration, and its speed after it has slid 2.4 m along the ramp.

  9. 9. Skidding to a stop: friction plus kinematics

    A car travelling at 22 m/s along a level road brakes so hard that the wheels lock and the tires skid. The coefficient of kinetic friction between the locked tires and the dry road is μk=0.72\mu_k = 0.72. How far does the car skid before it stops, and would a heavier car with identical tires skid further?

  10. 10. Down a ramp, then along the floor

    A 3.8 kg block is released from rest at the top of a ramp inclined at 25∘25^\circ. On the ramp, μs=0.35\mu_s = 0.35 and μk=0.28\mu_k = 0.28. The block slides 2.5 m down the ramp and then continues onto a level floor, where the coefficient of kinetic friction is μk=0.34\mu_k = 0.34. Treat the join between ramp and floor as smooth, so the block keeps its speed as it arrives. How far along the floor does the block slide before it stops?

  11. 11. Explain why: the contact area is missing from the model

    A rectangular wooden block has one face measuring 20 cm by 10 cm and another measuring 20 cm by 5 cm. A student slides it across a bench at constant speed, first resting on the large face and then on the small face, and measures the same kinetic friction force both times even though the second footprint is half the area. Explain why the model predicts this, and state what the coefficient of kinetic friction does depend on.

Friction: answer key

  1. Ff,k=67 NF_{f,k} = 67\ \text{N}, directed opposite the crate's velocity. The crate's mass never entered the calculation, because the normal force was handed to you instead of being computed from a weight.

  2. FN=147 NF_N = 147\ \text{N} and Ff,k=62 NF_{f,k} = 62\ \text{N}. Writing FN=mgF_N = mg was legitimate here only because the floor is level and nothing else acts on the toolbox vertically. Problem 5 breaks the second of those conditions and problem 6 breaks the first.

  3. μk=0.26\mu_k = 0.26, with no units. The 0.20 m/s was given only to tell you the block was moving at constant velocity. The speed itself never appears in the arithmetic, and dragging the block twice as fast would give the same coefficient.

  4. (a) The crate does not move, and static friction is 140 N140\ \text{N} backwards, not 158 N. (b) Any push above 158 N158\ \text{N}. (c) a=3.0 m/s2a = 3.0\ \text{m/s}^2 forwards. Friction on this crate drops from 158 N at the instant it breaks loose to 122 N once it is sliding, which is why a heavy crate lurches forwards as it starts.

  5. FN=67 NF_N = 67\ \text{N}, Ff,k=15 NF_{f,k} = 15\ \text{N}, and a=2.8 m/s2a = 2.8\ \text{m/s}^2 in the direction of the pull. The normal force sits 21 N below the box's 88 N weight, and every friction number downstream inherits that. Angle the rope more steeply and the floor supports less still; angle the pull downwards instead and you would add the vertical component rather than subtract it.

  6. The box stays put. Static friction is 26 N26\ \text{N} acting up the slope, well under the 40 N40\ \text{N} maximum this surface could have supplied. About 13 N of capacity goes unused, which is why the box would still hold if you loaded it or tilted the plank somewhat further.

  7. The washer begins to slide at θc=36.5∘\theta_c = 36.5^\circ, about 37∘37^\circ to two significant figures. A second stacked washer changes nothing, because tan⁡θc=μs\tan\theta_c = \mu_s contains no mass. That independence is exactly why tilting a surface until an object slips is a standard way to measure μs\mu_s with no scale and no force sensor.

  8. Ff,k=25 NF_{f,k} = 25\ \text{N} up the slope, a=4.3 m/s2a = 4.3\ \text{m/s}^2 down the slope, and v=4.5 m/sv = 4.5\ \text{m/s} after 2.4 m. The acceleration does not depend on the 11 kg: any block with μk=0.31\mu_k = 0.31 on a 42∘42^\circ ramp accelerates at 4.3 m/s24.3\ \text{m/s}^2. The mass was needed only for the friction force in newtons.

  9. The car skids 34 m34\ \text{m}. A heavier car with the same tires skids exactly as far, because the mass cancels: Δx=v02/(2μkg)\Delta x = v_0^2 / (2\mu_k g) contains no mm. Speed is the variable that matters, and it is squared, so a car at 44 m/s would need four times the distance.

  10. The block slides about 1.2 m1.2\ \text{m} along the floor. The 3.8 kg cancels at every stage and never affects the answer. Notice how differently the three coefficients are used: μs=0.35\mu_s = 0.35 only decides whether the block moves, while μk=0.28\mu_k = 0.28 and μk=0.34\mu_k = 0.34 decide how fast it gets going and how soon it stops.

  11. Because Ff,k=μkFNF_{f,k} = \mu_k F_N contains no area term, and neither of its two inputs changed when the block was turned over. The CED says so directly in essential knowledge 2.7.A.1.ii, that friction between two surfaces does not depend on the size of the contact area. The coefficient depends instead on the material properties of both surfaces in contact, per essential knowledge 2.7.A.2.i.

The key gives final answers only. The full worked solution for each problem is on the matching practice set, and every other sheet is on the worksheets page.