AP Physics C E&M · Experimental Design and Analysis

Wire resistivity lab: AP Physics C E&M FRQ Practice

2 versions of one AP Physics C E&M free-response question of the Experimental Design and Analysis type, each with a 10-point rubric and a full solution. Write your response on paper before you open the rubric.

These are PhysicsLearn originals written in the AP style, not released exam questions. Topics: 11.3 Resistance, Resistivity, and Ohm's Law.

Version 1

A student has uniform wire with cross-sectional area 0.4 mm^2 and wants to determine its resistivity. A sample length is 1 m.

  1. Part A. Design a procedure using several wire lengths. Identify variables and controlled quantities.
  2. Part B. Choose graph axes and derive how the slope determines resistivity.
  3. Part C. Calculate the expected slope and resistance of the sample length. Explain how to limit heating effects.
Show the rubric and solution

Part A: 4 points

Vary wire length, measure voltage across and current through each length, and calculate R = V/I.

Keep wire material, cross-sectional area, and temperature fixed. Use at least six lengths.

  • 1 point. Identifies wire length as the independent variable.
  • 1 point. Identifies resistance as the dependent variable.
  • 1 point. Explains how resistance is measured.
  • 1 point. Names relevant controlled variables.

Part B: 3 points

From R = rho L/A, plot resistance vertically against length horizontally.

The slope is rho/A. The area is 4.000000000e-7 m^2, so the expected slope is 0.038 ohms/m.

  • 1 point. Chooses resistance versus length axes.
  • 1 point. Identifies slope as resistivity divided by area.
  • 1 point. Converts cross-sectional area to square meters.

Part C: 3 points

The expected slope is rho/A = 0.038 ohms/m, giving R = slope times L = 0.038 ohms.

Use small currents and take readings promptly so the wire temperature and resistivity do not rise appreciably.

  • 1 point. Calculates the expected slope.
  • 1 point. Calculates the sample resistance.
  • 1 point. Provides a valid temperature-control method.

Version 2

A student has uniform wire with cross-sectional area 0.6 mm^2 and wants to determine its resistivity. A sample length is 1.4 m.

  1. Part A. Design a procedure using several wire lengths. Identify variables and controlled quantities.
  2. Part B. Choose graph axes and derive how the slope determines resistivity.
  3. Part C. Calculate the expected slope and resistance of the sample length. Explain how to limit heating effects.
Show the rubric and solution

Part A: 4 points

Vary wire length, measure voltage across and current through each length, and calculate R = V/I.

Keep wire material, cross-sectional area, and temperature fixed. Use at least six lengths.

  • 1 point. Identifies wire length as the independent variable.
  • 1 point. Identifies resistance as the dependent variable.
  • 1 point. Explains how resistance is measured.
  • 1 point. Names relevant controlled variables.

Part B: 3 points

From R = rho L/A, plot resistance vertically against length horizontally.

The slope is rho/A. The area is 6.000000000e-7 m^2, so the expected slope is 0.032 ohms/m.

  • 1 point. Chooses resistance versus length axes.
  • 1 point. Identifies slope as resistivity divided by area.
  • 1 point. Converts cross-sectional area to square meters.

Part C: 3 points

The expected slope is rho/A = 0.032 ohms/m, giving R = slope times L = 0.044 ohms.

Use small currents and take readings promptly so the wire temperature and resistivity do not rise appreciably.

  • 1 point. Calculates the expected slope.
  • 1 point. Calculates the sample resistance.
  • 1 point. Provides a valid temperature-control method.

Keep going